Average Reviews:
(More customer reviews)I needed to wirelessly network a Brooklyn Brownstone approximately 45' long by 100 feet tall 4 floors. Initially started with the Netgear
RANGEMAX WIRELESS ROUTER Netgear RangeMax Wireless Router (WPN824)because of the advertised (last year Sept)
-MIMO (Multi-In, Multi-Out) technology boosts network performance with up to 10x the speed and 10x the coverage of Wireless-G
Result: Signal traveled straight up to the upper floor without a problem, but could not reach the rooms from the middle to the front of the house 2nd ,3rd ,or 4th floors (Comcast cable modem placed on the second floor back). Mysteriously connections would drop without reason from time to time. Theory Comcast equipment was causing that problem, too, wireless phone and fax interference too being the possible gremlins.
Phase 2-Linksys Wireless-G Range Expander WRE54G
used 3 Linksys Wireless G Extenders to act as repeaters on the upper floors. Could only manage to get a strong signal partially to the second floor but signal was intermittent. Could only link two extenders but the second, again dropped the signal intermittently and the dreaded `limited or no connectivity' message began. Observation proved these messages materialized while roaming-connecting to the second or third node (first node being Netgear WPN824). Though the signal was seen (in some cases very good) Netgear had a time issuing IP addresses past the first node.
Phase 3, after spending 1 whole day surfing the net for info. I decided to start anew....after much comparing and no reviews to go by. I decided on the Linksys WAP 200 because of its versatility and advertised signal strength - it could be an accesspoint, a repeater, or a bridge...and because I had the G extenders from Linksys that I became familiar with....
200AP2 Linsys WAP200
Setup 1- Continue the Netgear as the Ethernet to cable box, wireless access point, with DHCP server, using the 2 200's as repeaters. The main problem, after becoming familiar with the WAP200 was still the `Limited or no connectivity' message. I `trial and erred' the settings ,I observed a correlation between RIP and the error msg.I also noted the msg occurring much more on my older lap (XP home), vs my girl friends newer (XP) lap.
Setup 2- using the Netgear as the DHCP server, Ethernet to cable box SWITCH. One of the 200's would account for a wireless access point (located on the second floor, 2 ft from the Netgear), the other a 200 a Repeater (3rd floor hall...I added a Hawking Technology's HAI15SC,Hawking HAI15SC 15dBi Hi-Gain Directional Corner Antenna 2.4GHz Hi-Gain Wireless Corner Antenna, boosts your wireless signal strength from 2dBi (standard) to 15dBi to the second floor 200...didn't think I needed it). This configuration covered the whole house, there were a few low signal readings at the extreme ends on the 4th floor 3ft from the front window , which I intended to eliminate with the Linksys G Extender.
Which brings me to the only concern- AP Mode gives you the opportunity to use the 200 in either 1 of 3 modes
AP Mode Screen
Use this screen to configure the Access Point mode. The three available modes are Access Point, Wireless Repeater, and Wireless Bridge.
The 200 that was used as the wireless access point needed the MAC address of the 200 used as a Repeater (in Repeater mode-- max 3 MAC addresses). Adding the address of the second wap200 (as Repeater) was'nt an issue, all worked perfectly. When I added the MAC addresses of the G Extenders `Limited connectivity' messages again appeared, I tried various combo's including changing the order but always a problem...perhaps the repeaters have to be legit repeaters or WAP200's...anywho I found this interesting and will be taking the 3 extenders back to Best Buy
Conclusions-
overall I found the Linksys WAP 200 a really good product. I don't believe you have to know the nuts and bolts about networking to get the WAP200 up and running. The documentation will not be of help to a newbie, but if you google your concerns you may learn a thing or two. $124 is a really good price for the endless possibilities one could use this 3-in-1 wireless network product......btw I speed tested the connections, watched video (google video, Youtube) while roaming around the house and it never dropped a signal.
it is now 11-28-2008 and this product has been running non stop since the original review..
asH
Click Here to see more reviews about:
Wireless G Access Point w/ P.O.E. and Rangebooster.The Linksys WAP200 Access Point lets you connect Wireless-G (802.11g) or Wireless-B (802.11b) devices to your wired network so you can add PCs to the network with no cabling hassle. Power over Ethernet support makes it easy to install -- you can mount the Access Point anywhere, even without ready access to a power plug. With appropriate Power Over Ethernet support at the other end, you only need to run one cable to the Access Point to deliver both data and power. Of course, you can also use the included AC adapter if your installation point has power available nearby. Moreover, the integrated QoS features provide consistent voice and video quality on both the wired and wireless networks, enabling the deployment of business qualilty VoIP and video applications.
Get 10% OFF
Click here for more information about Wireless G Access Point w/ P.O.E. and Rangebooster.
